博客网 >

Description

This document describes how to recover a password on a Cisco cs500 communication server.

The Cisco cs500 does not have a console port so to recover a password you must erase the configuration then configure the server again.

Step-by-Step Procedure

1.Unplug the Cisco cs500 server.

2.Press and hold the DEFAULT button on the front of the chassis.

3.Turn on the server.

The OK and LAN LEDs blink on and off.

4.When the OK and LAN LEDs blink off (after about 15 seconds), release the DEFAULT button.

The 500-CS enters setup mode in about two to ten minutes.

5.Configure the server.


Cisco路由器口令的恢复(800)

Description

This document describes the password recovery procedure for the Cisco 800.

Step-by-Step Procedure

Attach a terminal or PC with terminal emulation to the console port of the router. Use the following terminal settings:

9600 baud rate

No parity

8 data bits

1 stop bit

The required console cable specifications are described in Cabling Guide for RJ-45 Console and AUX Ports (Cisco's 1000 series, 2500 series, and AS5100).

Type show version and record the setting of the configuration register. Click here to see output of a show version command.

The configuration register setting is usually 0x2102 or 0x102.

Using the switch, turn off the router and then turn it on.

Press Break on the terminal keyboard within 60 seconds of the powerup to put the router into ROMMON.

If the break sequence doesn't work, see Possible Key Combinations for Break Sequence During Password Recovery for other key combinations.

Type set ios-conf = 142 at the boot# prompt.

If Flash is intact, the best setting is 0x42.

If the Flash is not installed or is erased, use the 0x41 setting. Note that with this setting you can view or erase the configuration but cannot change the password.

Type boot at the boot#> prompt to initialize the router.

The router reboots but ignores its saved configuration.

Type no after each setup question or press Ctrl-C to skip the initial setup procedure.

Type enable at the Router> prompt.

You'll be in enable mode and see the Router# prompt.

Important Type config mem or copy start running to copy the nonvolatile RAM (NVRAM) into memory. Do not type config term.

Type wr term or show running.

The show running and wr term commands show the configuration of the router. In this configuration you see under all the interfaces the shutdown command, which means all interfaces are currently shutdown. Also, you can see the passwords either in encrypted or unencrypted format.

Type config term and make the changes.

The prompt is now hostname(config)#.

Type enable secret .

Issue the no shutdown command on every interface that is used. If you issue a show ip interface brief command, every interface that you want to use should be "up up".

Type config-register 0x2102, or the value you recorded in step 2.

Press Ctrl-z to leave the configuration mode.

The prompt is now hostname#.

16.Type write mem or copy running startup to commit the changes.

Router>show version

Cisco Internetwork Operating System Software

IOS (tm) C800 Software

(C800-Y6-MW), Version 12.1(1), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 14-Mar-00 16:01 by cmong

Image text-base: 0x000EA000, data-base: 0x005D3000


ROM: TinyROM version 1.0(3)

Router uptime is 2 days, 3 hours, 8 minutes

System returned to ROM by power-on

System image file is "flash:c800-y6-mw.121-1"

Cisco C801 (MPC850) processor (revision 0) with 51428K bytes of virtual memory.

Processor board ID JAD03050229

CPU part number 33

Bridging software.

Basic Rate ISDN software, Version 1.1.

1 Ethernet/IEEE 802.3 interface(s)

1 ISDN Basic Rate interface(s)

12M bytes of physical memory (DRAM)

8K bytes of non-volatile configuration memory

8M bytes of flash on board (4M from flash card)

Configuration register is 0x2102

!--- The router was just powercycled and during bootup a break sequence was sent to the router.

TinyROM version 1.0(3)

Fri Apr 30 18:22:12 1999

Copyright (c) 1998-1999 by cisco Systems, Inc.

All rights reserved.

POST ......... OK. 12MB DRAM, 8MB Flash.

boot# set ios-conf = 142

boot# boot

Booting "c800-y6-mw.121-1" ...,

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C800 Software (C800-Y6-MW), Version

12.1(1), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 14-Mar-00 16:01 by cmong

Image text-base: 0x000EA000, data-base: 0x005D3000

Cisco C801 (MPC850) processor (revision 0) with 51428K bytes of virtual memory.

Processor board ID JAD03050229

CPU part number 33

Bridging software.

Basic Rate ISDN software, Version 1.1.

1 Ethernet/IEEE 802.3 interface(s)

1 ISDN Basic Rate interface(s)

12M bytes of physical memory (DRAM)

8K bytes of non-volatile configuration memory

8M bytes of flash on board (4M from flash card)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started! (press Enter)

00:01:45: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) C800 Software (C800-Y6-MW), Version 12.1(1), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Tue 14-Mar-00 16:01 cmong

00:01:45: %LINK-5-CHANGED: Inte

rface BRI0, changed state to administratively down

00:01:45: %LINK-5-CHANGED: Interface Ethernet0, changed state to administratively down

00:01:46: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, changed state to down

00:01:46: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down

Router>en

Router#copy start run

Destination filename [running-config]? (press Enter)

2010 bytes copied in 32.120 secs (62 bytes/sec)

Router#

Router#

00:02:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down

00:02:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to down

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#enable secret cisco

Router(config)#

00:03:39: %SYS-5-CONFIG_I: Configured from console by console


Router#sh ip int brief

Interface   IP-Address      OK?    Method   Status                 Protocol

BRI0        unassigned      YES    TFTP     administratively down  down

BRI0:1      unassigned      YES    unset    administratively down  down

BRI0:2      unassigned      YES    unset    administratively down  down

Dialer0     unassigned      YES    TFTP     up                     up

Dialer1     192.168.32.1    YES    TFTP     up                     up

Ethernet0   10.200.40.65    YES    TFTP     administratively down  down

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int e 0

Router(config-if)#no shut

Router(config-if)#

00:04:02: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up

00:04:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up

Router(config)#config-reg 0x2102

Router(config)#^Z

Router#

00:04:36: %SYS-5-CONFIG_I: Configured from console by console

Router#write mem

<< This document de... / 适用于所有的2000系列、250... >>

专题推荐

不平凡的水果世界

不平凡的水果世界

平凡的水果世界,平凡中的不平凡。 今朝看水果是水果 ,看水果还是水果 ,看水果已不是水果。这境界,谁人可比?在不平凡的水果世界里,仁者见仁,智者见智。

中国春节的那些习俗

中国春节的那些习俗

正月是农历新年的开始,人们往往将它看作是新的一年年运好坏的兆示期。所以,过年的时候“禁忌”特别多。当然,各个地方的风俗习惯不一样,过年的禁忌也是不一样的。

评论
0/200
表情 验证码:

danyi2007

  • 文章总数0
  • 画报总数0
  • 画报点击数0
  • 文章点击数0
个人排行
        博文分类
        日期归档